Energy release rates in a constrained epoxy disc with Hookean and Mooney–Rivlin materials

Assuming that the disc material can be modeled either as Mooney–Rivlin or as Hookean and the steel ring enclosing the disc as Hookean, the energy release rates as a function of the crack length are evaluated and compared. Two loadings are considered––one in which the surface of the star shape hole in the disc is loaded by a uniform pressure and the other in which the temperature of the composite body is uniformly raised. It is found that the linear and the nonlinear analyses give qualitatively similar results for the two loadings. For each load, the energy release rate increases with an increase in the starter crack length, reaches a maximum value and then decreases gradually.     

Experiments on crack identification in cantilever beams

In this paper we present an experimental investigation of the identification of crack location and size. By providing the first three natural frequencies through vibration measurements, curves of crack equivalent stiffness versus crack location are plotted, and the intersection of the three curves predicts the crack location and size. In the experiments, the cracked specimens were made using a wire-cut electrical discharge machine, and the cantilever beams were excited next to the free end by means of an impulse force hammer. In order to obtain the accurate natural frequencies from the transient signal measured, the method of zoom fast Fourier transform is adopted to improve frequency resolution. From experimental results, it is observed that the identification errors of crack location and size are less than 2% and 4%, respectively. The effectiveness of crack identification through vibration measurements is verified.     

Some aspects of linear and nonlinear viscoelastic behaviour of polymer melts in shear

In linear viscoelastic investigations the frequency dependence of the phase shift between stress and strain appears to be very characteristic of the molecular structure of the material. This function is also a good approximation of the slope of the double logarithmic plot of the absolute value of the shear modulusG _d vs. the angular frequency. The product (G _d /) sin 2 comes very close to the relaxation spectrumH(), with = 1/, in all physical states of the material.The experimentally observed separability of time and strain effects in nonlinear viscoelasticity of highly viscous isotropic polymer fluids imposes restraints to the form of the constitutive equation. A single integral superposition equation of the Boltzmann type containing the product of a time function and a nonlinear strain function gives good results in describing experimental data in shear as well as in elongation. The molecular structure affects both functions in a different way. A universal definition of the nonlinear tensorial strain measure has not yet been developed. There are some indications that a definition on the basis of the principal stretch ratios may be fruitful.Invited paper, presented at the First Conference of European Rheologists at Graz (Austria), April 14–16, 1982.     

The effects of forced boundary conditions on flow within a cubic cavity using digital particle image thermometry and velocimetry (DPITV)

Buoyancy-driven convection within a cavity, whose sidewalls are heated and cooled, is a problem of great interest, because it has applications in heat transfer and mixing. Most studies to date have studied one of two cases: the steady-state case or the development of the transient flow as it approaches steady state. Our main concern was to study the response of the cavity to time-varying thermal boundary conditions. We therefore decided to observe the flow phenomena within a convection cavity under sinusoidal thermal forcing of the sidewalls. To map the flow properly, it is necessary to have simultaneous kinematic and thermal information. Therefore, the digital particle image thermometry and velocimetry (DPITV) is used to acquire data. Implementing this technique requires seeding the flow with encapsulated liquid crystal particles and illuminating a cross section of the flow with a sheet of white light. Extraction of the thermal and kinematic content is in two parts. For the first, the liquid crystals will reflect different colors of the visible spectrum, depending on the temperatures to which they are subjected. Therefore, calibrating their color reflection with temperature allows for the extraction of the thermal content. For the second part, the kinematic information is obtained through the use of a digital cross-correlation particle image velocimetry technique. With the use of DPITV, the flow within a convection cavity is mapped and studied under steady forcing and sinusoidally forced boundary conditions at the Brunt-Väisälä frequency. For the sinusoidally forced case, three cases are studied. In the first, the heating between the two walls is in phase. In the second, the heating between the two walls is 180° out of phase. In the third, the heating between the two walls is 90° out of phase. For steady forcing, the thermal plots show that the flow develops a linearly stratified profile within the center of the cell. At the sidewalls, however, owing to forcing, hot/cold thermal boundary layers develop at the left/right walls. These hot/cold thermal boundary layers then turn around the upper-left/lower-right corners and develop into intrusion layers that extend across the top and bottom walls. The vorticity and streamlines show that the bulk of the fluid motion is concentrated around the walls, whereas the fluid within the center of the cell remains stationary. For the sinusoidally forced cases, the thermal plots show the existence of many thermal “islands,” or pockets of fluid where the temperature is different with respect to its surroundings. The vorticity plots show that the center of the cell is mostly devoid of vorticity and that the vorticity is mainly confined to the sidewalls, with some vorticity at the top and bottom walls. For the 0° forcing, the streamlines show the development of two counterrotating rollers. For the 180° forcing, the streamlines show the development of only one roller. Finally, for the 90° forcing, the streamlines show the development of both a two-roller and a one-roller system, depending on the position within the forcing cycle.     

A SIMPLIFIED CALCULATING METHOD OF NONLINEAR FREQUENCY OF CABLE NET UNDER MEAN WIND LOAD

The cable net supported glass curtain wallas the most advanced technique in dot point supported glass curtain wall, is widely used in China. Because of its large deflection and high nonlinearity under wind load, the dynamic performance of the cable net is greatly different from that of the conventional linear structures. The continuous membrane theory is used to construct the nonlinear vibration differential equation of the cable net, and the harmonic balance method is used to solve the analytic formula of the nonlinear frequency. In order to verify the accuracy of the above analytic formula, the results of the formula and the nonlinear FEM time-history method are compared and found to be in good agreement. Furthermore, the nonlinear vibration differential equation and the nonlinear frequency obtained in this paper are the basis for the wind-induced response analysis of a cable net under fluctuating wind load.     

FREE VIBRATION OF ANISOTROPIC RECTANGULAR PLATES BY GENERAL ANALYTICAL METHOD

According to the differential equation for transverse displacement function of anisotropic rectangular thin plates in free vibration, a general analytical solution is established. This general solution, composed of the composite solutions of trigonometric function and hyperbolic function, can satisfy the problem of arbitrary boundary conditions along four edges. The algebraic polynomial with double sine series solutions can also satisfy the problem of boundary conditions at four corners. Consequently, this general solution can be used to solve the vibration problem of anisotropic rectangular plates with arbitrary boundaries accurately. The integral constants can be determined by boundary conditions of four edges and four corners. Each natural frequency and vibration mode can be solved by the determinate of coefficient matrix from the homogeneous linear algebraic equations equal to zero. For example, a composite symmetric angle ply laminated plate with four edges clamped has been calculated and discussed.     

硅微机械谐振陀螺仪的非线性分析

给出了硅微机械谐振陀螺仪的结构,介绍了硅微机械谐振陀螺仪的工作原理,详细推导并给出了陀螺仪的输出频率和标度因数非线性的计算公式;基于影响谐振陀螺仪标度因数的参数,分析了由谐振器的振幅和梳齿静电驱动力引起的硅微机械谐振陀螺仪的非线性特性,给出了振动幅度与谐振频率关系的表达式.实验结果表明,陀螺仪的整体性能主要取决于谐振器振动幅度的稳定性.     

含压电层的功能梯度柱壳的自由振动分析

基于三维弹性理论，导出了带有压电层的圆柱形梯度壳的动力学方程以及相应的边界条件，用幂级数展开法得到了求解该圆柱形梯度壳自由振动的三维精确公式．通过实例模型求解了该壳体的自由振动的固有频率；分析了不同电学边界条件对壳体的振动频率的影响。结果可评估各种近似理论解和数值解的正确性。     

Dynamics of hybrid shafts

In this paper the dynamic performance and cross-section deformation of shafts made of metals (steel and aluminum), composites (CFRP and GFRP) and hybrids of metals and composites have been studied. A layered finite degenerated shell element with transverse shear deformation and dynamic behavior is employed. Results obtained show that improvements in dynamic performance and reduction of cross-section deformation of hybrid shafts over metallic and composite shafts are possible.     

DYNAMIC ANALYSIS OF A LOADED SHOULDER-POLE DURING WALKING

建立了扁担挑物的动力学模型和动力学方程,并进行了数值求解。扁担挑物时存在三种频率,即重物类似于单摆的振动频率、挑运者的步行频率和扁担-重物系统铅垂方向的振动频率。计算结果表明,为了获得较好的挑担体验,三种频率应该相互协调。当人挑担行走的频率为扁担-重物系统铅垂方向振动频率的70%,$\sim$,80%时,肩部铅垂附加动反力为重物重力的30%左右且与肩部铅垂运动同相,当重物类似于单摆的振动频率为人步行频率的25%,$\sim$,30%时,重物的摆角和肩部受到的水平附加动反力均较小,从而有利于人挑担行走。